THE VALVES IN THIS HEAD ARE MADE IN JAPAN !!! GREAT QUALITY THIS IS CLASSIFIED AS AN "OLD 70 HEAD" AND DOME. IT WILL REPLACE THE STOCK HEADS FROM 80 - 81 C70 PASSPORTS ALL CL/SL/XL70'S 69 - 81 CT70'S ALL ATC70'S ALL TRX70'S THE STOCK PISTONS FROM THE ABOVE MODELS WILL WORK WITH THIS HEAD.. IF YOU USE THE 85CC/51MM CYLINDER AND STOCK OR STROKER CRANK THEN YOU NEED OUR # (100041) PISTON.. OR IF YOU USE THE 88CC/52MM CYLINDER AND STOCK OR STROKER CRANK THEN YOU NEED OUR # (100042) PISTON.. BUT IF YOU WANT THE BIG 95CC/54MM CYLINDER AND STOCK OR STROKER CRANK THEN USE OUR # (54/GBO) PISTON!!!!!! LISTED BELOW ARE SOME DIFFERENT CAM OPTIONS, AND ANY REPLACEMENT COVERS OR PARTS YOU MAY NEED FOR THIS HEAD |
|
|
|
|
|
|
|
|
|
|
| FITS ALL Z50 TO 1981 CT70'S THRU 1981 PASSPORTS THRU 1981 ALL ATC70'S ALL TRX70'S ALL XL/CL/SL70'S |
|
|
| THIS CAM WILL WORK IN THE FOLLOWING HEADS 1968 TO 1981 Z50'S 1980 TO 1981 C70 PASSPORTS ALL CL/SL/XL 70'S CT70 FROM 1969 TO 1981 ALL ATC AND TRX 70'S YOU MAY WANT TO USE THE HD VALVE SPRINGS (NOT A MUST BUT NOT A BAD IDEA) |
|
|
| * * * * !! NOTE !! (THIS CAM MUST BE USED WITH STOCK HONDA VALVES) OR AT LEAST CHECK TO MAKE SURE THE AFTERMARKET VALVES CLEAR EACH OTHER WHEN THEY PASS EACH OTHER... (YOU CAN GRIND OFF SOME OF THE VALVE'S OUTTER OD SO THEY DO CLEAR IF NEEDED) WE RECCAMEND OUR 200159 VALVE SPRING, SO YOU DON'T GET COIL TO COIL BINDING THIS IS AS BIG OF CAM AS WILL FIT IN THE OLD TYPE HEADS IT HAS SOME LIFT OVER THE STOCK CAM, BUT TONS OF DURATION * THIS IS THE MOST RADICAL CAM MADE FOR THE OLD TYPE HONDA HEADS * THIS CAM HAS 6MM OF LIFT. * Camshaft Calculations - Lobe Center / Duration AT .050" VALVE LASH THE VALVE LASH IS MORE FOR CARS AND REALLY DON'T GIVE A TRUE CYCLE READING,, BUT THATS JUST HOW IT'S DONE. THE LASH IS ONLY .0025" ON THE BIKES COMPAIRED TO .050" ??? * THIS CAM has an Overlap of 40.00 degrees and has an Intake Duration of 255.00 degrees. The Exhaust Duration is 265.00 degrees. The Inlet Cam has an Installed Centerline of 102.50 degrees ATDC. The exhaust cam has an Installed Centerline of 117.50 degrees BTDC. * LIFT IS 6MM THE BEARING IS A PRESS FIT (TAP IN WITH COMMON SOCKET) |
|
|
| ALSO WORK TO REPLACE STOCK 50 AND 70 STOCK SPRINGS AND ADD SOME MORE TENSION |
|
|
|
|
|
|
|
|
| THIS COMPRESSOR IS SOMETHING I CAME ACROSS FROM THE SMALL ENGINE REPAIR WORLD. IT ACCUALLY WORKS BETTER THAN MY $140.00 OEM HONDA COMPRESSOR, BECAUSE THERE IS NOTHING IN THE WAY WHEN TRING TO REMOVE AND REPLACE THE COTTORS YAHOO !!! SEE ALL THE PICTURES BELOW FOR INSTRUCTIONS. ONE TINY ITEM WITH THIS COMPRESSOR, YOU MUST GRIND SOME OFF THE ONE ARM. SEE BELOW,, MAKE THE SMALLER ARM LOOK LIKE THE ONE ON THE COMPRESSOR IN THE PICTURE. IT TOOK ME ABOUT 45 SECONDS WITH MY 4 1/2" ANGLE GRINGER TO DO THIS. CLICK ON ANY OF THE PICTURES BELOW TO GET A LARGER VIEW. |
|
|
| THESE WILL FIT INTAKE OR EXHAUST. ON ALL Z50 CT70 C70. also fits all years of ct110's |
|